模块化永磁直线游标电机等效磁网络及漏磁分析

在模块化永磁直线游标电机的初始设计及优化设计中,使用有限元方法(FEM)计算漏磁系数时需要耗费大量的建模和计算时间。针对这一问题,建立该种电机的等效磁网络模型,在建模期间,考虑气隙中的边缘效应,并计算永磁体组与定子齿在不同相对位置时的等效磁导,得到该种电机在一个周期内不同相对位置时的漏磁磁导和漏磁系数的数学解析表达式。采用FEM验证了该数学解析表达式的准确性。研究结果为模块化永磁直线游标电机的设计提供了理论依据。     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

一种开关磁阻电机无位置传感器控制效率优化策略

针对开关磁阻电机(SRM)的简化磁链法只能实现单相导通运行且导通区间固定的缺点,提出了一种结合固定关断角和自适应调节开通角的无位置传感器控制技术。利用曲线拟合关断位置磁链取代传统存储数据表,通过对比实时计算的动态磁链和曲线拟合的静态磁链,确定关断位置信号并估计转速和其他位置。考虑电机阻抗和电感的非线性特点,优化电感最小区域的开通角自调节模型确定导通区间。仿真结果验证了该方案的可行性和正确性,能够实现转子位置的间接检测,电机的运行效率得到进一步优化。     

Variation of dayside chorus waves associated with solar wind dynamic pressure based on MMS observations

The whistler-mode chorus waves are one of the most important plasma waves in the Earth’s magnetosphere. Generally, the amplitude of whistler-mode chorus waves prefers to strengthen when the energetic fluxes of anisotropic electrons increase outside the plasmapause. This characteristic is commonly associated with the geomagnetic storms or substorms. However, the relationship between the solar wind dynamic pressure (P_sw) and the long-time variation of chorus waves during the quiet period of the geomagnetic activity still needs more detailed investigations. In this paper, based on MMS observations, we present a chorus event just observed in the inner side of magnetopause without obvious geomagnetic storms or substroms. Interestingly, during this time interval, some P_sw fluctuations were recorded. Both the amplitudes and frequencies of chorus waves changed as a response to the variation in P_sw. It proved that the enhancement of P_sw increases the energetic electrons fluxes, which provides free energies for the chorus amplification. Furthermore, the wave growth rates calculated using linear theory increases and the central frequency of the chorus waves shifts to a higher frequency when the P_sw enhancement is greater, which are also consistent well with the observations. The results provide a direct evidence that the P_sw play an important role in the long-time variation of whistler-mode chorus waves inside the magnetopause.     

场协同原理在高超声速化学非平衡流动中的推广

应用理论分析与数值模拟方法，将对流传热的场协同原理从不可压缩流动推广至高超声速化学非平衡流动中。结果表明，高超声速化学非平衡层流与湍流的热流密度取决于流动的当地单位体积的动量与单位质量总焓梯度的协同。用当地单位体积的动量与单位质量总焓梯度的协同研究高超声速化学非平衡流动的壁面传热问题，对层流流动下的对流传热，不但计及了高超声速化学非平衡流的密度变化对热流密度的影响，而且包括了静焓梯度、压力梯度、边界层内的分子黏性剪切效应对热流密度的作用；对湍流问题，除了上述层流流动各项对热流密度的影响外，还计及了雷诺剪切应力对热流密度的作用。考虑到高超声速化学非平衡流静焓的定义，高超声速化学非平衡层流及湍流的场协同同时计及所有组分的平动能、转动能、振动能及电子能等梯度的贡献。     

Modeling and analysis of mover gaps in tubular moving-magnet linear oscillating motors

A tubular moving-magnet linear oscillating motor (TMMLOM) has merits of high efficiency and excellent dynamic capability. To enhance the thrust performance, quasi-Halbach permanent magnet (PM) arrays are arranged on its mover in the application of a linear electro-hydrostatic actuator in more electric aircraft. The arrays are assembled by several individual segments, which lead to gaps between them inevitably. To investigate the effects of the gaps on the radial magnetic flux density and the machine thrust in this paper, an analytical model is built considering both axial and radial gaps. The model is validated by finite element simulations and experimental results. Distributions of the magnetic flux are described in condition of different sizes of radial and axial gaps. Besides, the output force is also discussed in normal and end windings. Finally, the model has demonstrated that both kinds of gaps have a negative effect on the thrust, and the linear motor is more sensitive to radial ones.     

基于合成射流的旋翼翼型动态失速控制研究

针对直升机旋翼工作环境下来流速度和迎角(Angle of attack,AoA)耦合引起的动态失速问题,建立了基于合成射流的旋翼动态失速控制的数值模拟方法。采用运动嵌套网格方法,通过对翼型的平移和旋转实现变来流速度-变迎角的耦合。以积分形式的雷诺平均N-S方程为主控方程,空间离散使用Roe格式,时间离散为隐式LU-SGS方法,以OA209翼型为研究对象,在翼型上表面放置合成射流激振器,开展了射流位置、动量系数、无量纲频率以及偏角等参数对轻度失速、深度失速下翼型动态失速控制的研究。研究发现,轻度失速下,射流位置靠近气流分离点时(20%c附近,c为翼型弦长),对逆压梯度引起的轻度失速控制效果最佳。深度失速下气流分离点虽在5%c之前,但射流位于前缘分离泡后端(10%c附近)时控制效果较好。大迎角需要较大的动量系数才能有效控制。射流频率对涡结构的尺寸和数量会产生一定影响,能改变气动特性波动幅度。较小的射流偏角对轻度失速的控制更有效,而深度失速则需要较大的偏角。     

热防护系统损伤容限分析

建立了含初始矩形损伤的热防护系统(Thermal protection system,TPS)气动热分析的CFD数值模型,分析结果表明损伤区域侧壁出现了很高的热流密度峰值,并且迎风面侧壁峰值高于背风面,而损伤区域底部热流密度却很低。利用分析获得的热流密度建立了含损伤和无损伤TPS的有限元传热分析模型。分析结果表明:损伤的存在导致防热瓦最高温度急剧上升,超过其材料能承受的极限温度(1 500℃),防热瓦首先失效,而损伤对机体最高温度影响较小。最后进行了TPS损伤容限分析,在防热瓦极限温度约束下,外部热流密度最大值从100kW/m2增加到140kW/m2,矩形损伤宽度最大容许值从22.7mm减小到12.6mm,而弧形损伤宽度最大容许值从34.6mm减小到25.1mm,即随着外部热流密度最大值增加,损伤宽度的最大容许值降低,并且相同外部热流密度水平下弧形损伤宽度的最大容许值大于矩形损伤。     

低温磨料气射流加工PDMS实验研究

通过自研的低温磨料气射流加工装置进行低温磨料气射流加工聚二甲基硅氧烷(polydimethylsiloxane,PDMS)实验研究,分析了加工时间、加工距离、冲蚀角度和磨料粒径对冲蚀率、孔深和孔横截面形貌的影响。结果表明:随着加工时间的增加,冲蚀率先增大后减小,在第1阶段加工过程中,孔深与加工时间大致呈线性关系,增加加工时间还可使孔底部变平整;存在一个最佳加工距离使孔深最大,当加工距离大于最大加工距离时,孔深将随着加工距离的增加而急剧下降,孔的锥度随着加工距离的增大而增大;当冲蚀角度处于30°～60°之间时,冲蚀率最大,随着冲蚀角度的增加,孔的形状逐步由椭圆形变成圆形;存在一个最佳磨料粒径,使冲蚀率和孔深达到最大;当冲蚀角度小于90°时,低温磨料气射流加工PDMS材料去除机理为塑性去除和脆性去除的结合。     

Numerical analysis of hypersonic thermochemical non-equilibrium environment for an entry configuration in ionized flow

A theoretical methodology for thermochemical non-equilibrium flow combing with the HLLC (Harten-Lax-van Leer Contact) scheme was applied to study the hypersonic thermochemical non-equilibrium environment of an entry configuration in ionized flow. A two-temperature controlling model was utilized and the Gupta’s 11 species (N₂, O₂, NO, O, N, NO⁺, N₂⁺, O₂⁺, N⁺, O⁺, e^?) thermochemical non-equilibrium model was taken. Firstly, numerical calculations of hypersonic thermochemical non-equilibrium environments for different aerodynamic shapes were carried out to verify the reliability of the method above. Then, the method was used to research the effects of ionization and wall catalysis on the hypersonic thermochemical non-equilibrium environment of the entry configuration in ionized flow. The shock stand-off distance can be reduced by thermochemical reactions but doesn’t continue to decrease significantly when ionization occurs. The shock stand-off distance calculated by the 11 species model is 4.2% smaller than that calculated by the 5 species (N₂, O₂, NO, O, N) thermochemical non-equilibrium model without considering ionization. Ionization reduces wall heat flux but increases wall pressure a little. The effect of ionization on aerothermal loads is greater than that of aerodynamic loads. The thermochemical reactions of electrons and ions catalyzed at the wall increase wall heat flux significantly but make a small change in wall pressure. The maximum wall heat flux obtained by only considering the electrons and ions catalyzed at the partially catalytic wall condition is 11.8% less than that calculated at the super-catalytic wall condition.